- Frequently Asked Questions >
- FAQ: Replication and Replica Sets
FAQ: Replication and Replica Sets¶
This document answers common questions about database replication in MongoDB.
What kinds of replication does MongoDB support?¶
MongoDB supports master-slave replication and a variation on master-slave replication known as replica sets. Replica sets are the recommended replication topology.
What do the terms “primary” and “master” mean?¶
In a replica set, if the current “primary” node fails or becomes inaccessible, the other members can autonomously elect one of the other members of the set to be the new “primary”.
By default, clients send all reads to the primary; however, read preference is configurable at the client level on a per-connection basis, which makes it possible to send reads to secondary nodes instead.
What do the terms “secondary” and “slave” mean?¶
Replication operates by way of an oplog, from which secondary/slave members apply new operations to themselves. This replication process is asynchronous, so secondary/slave nodes may not always reflect the latest writes to the primary. But usually, the gap between the primary and secondary nodes is just few milliseconds on a local network connection.
How long does replica set failover take?¶
It varies, but a replica set will select a new primary within a minute.
The election itself may take another 10-30 seconds.
Does replication work over the Internet and WAN connections?¶
Can MongoDB replicate over a “noisy” connection?¶
Yes, but not without connection failures and the obvious latency.
Members of the set will attempt to reconnect to the other members of the set in response to networking flaps. This does not require administrator intervention. However, if the network connections among the nodes in the replica set are very slow, it might not be possible for the members of the node to keep up with the replication.
What is the preferred replication method: master/slave or replica sets?¶
New in version 1.8.
What is the preferred replication method: replica sets or replica pairs?¶
Deprecated since version 1.6.
Why use journaling if replication already provides data redundancy?¶
Journaling is particularly useful for protection against power failures, especially if your replica set resides in a single data center or power circuit.
Journaling requires some resource overhead for write operations. Journaling has no effect on read performance, however.
Journaling is enabled by default on all 64-bit builds of MongoDB v2.0 and greater.
Are write operations durable if write concern does not acknowledge writes?¶
However, if you want confirmation that a given write has arrived at the server, use write concern.
After the default write concern change, the default write concern acknowledges all write operations, and unacknowledged writes must be explicitly configured. See the MongoDB Drivers and Client Libraries documentation for your driver for more information.
How many arbiters do replica sets need?¶
Replica sets require a majority of the remaining nodes present to elect a primary. Arbiters allow you to construct this majority without the overhead of adding replicating nodes to the system.
There are many possible replica set architectures.
A replica set with an odd number of voting nodes does not need an arbiter.
A common configuration consists of two replicating nodes that include a primary and a secondary, as well as an arbiter for the third node. This configuration makes it possible for the set to elect a primary in the event of failure, without requiring three replicating nodes.
You may also consider adding an arbiter to a set if it has an equal number of nodes in two facilities and network partitions between the facilities are possible. In these cases, the arbiter will break the tie between the two facilities and allow the set to elect a new primary.
What information do arbiters exchange with the rest of the replica set?¶
Arbiters never receive the contents of a collection but do exchange the following data with the rest of the replica set:
- Credentials used to authenticate the arbiter with the replica set. All MongoDB processes within a replica set use keyfiles. These exchanges are encrypted.
- Replica set configuration data and voting data. This information is not encrypted. Only credential exchanges are encrypted.
If your MongoDB deployment uses SSL, then all communications between arbiters and the other members of the replica set are secure. See the documentation for Configure mongod and mongos for SSL for more information. Run all arbiters on secure networks, as with all MongoDB components.
The overview of Arbiter Members of Replica Sets.
Which members of a replica set vote in elections?¶
Additionally, the state of the voting members also determine whether the member can vote. Only voting members in the following states are eligible to vote:
Is it normal for replica set members to use different amounts of disk space?¶
Factors including: different oplog sizes, different levels of storage fragmentation, and MongoDB’s data file pre-allocation can lead to some variation in storage utilization between nodes. Storage use disparities will be most pronounced when you add members at different times.